After all the strings are secured, you can finally release the tension of the rod and start to tie the ends of the strings to make sure they stay in place. You will need to use some needle-nose pliers and an awl when necessary. Tie a knot from the short end on one of the vertical strings and then cut off the excess string.
Now you will need to begin stringing the cross pattern. This is done by going the opposite direction of the currently installed string. Insert the string into the hole and weave it the same way you did the other string. The only difference here is that you will need to weave the string over and under the main string as you go. Make sure you keep a consistent amount of tension when you string, as this will help ensure that the tennis racquet is accurately shaped.
Lastly, thread the last crossing strings back into the main grommets and then make sure to tie it securely at the end. Make sure to knot it with a needle-nose plier, as this can help ensure that the tennis racquet looks good. The estimated time that it will take you to completely restring a tennis racquet is going to be highly dependent on what tools and methods you are using.
If this is your first time restringing a racquet, then you can expect it to take over an hour. Here's a video instruction to guide you. Just make sure that each string is pulled independently and never more than one string at a time. Hopefully, this has answered your question of, " how long does it take to string a tennis racket? Have another question? You can use your pliers or insert the end of the string into the gripper to tighten it, and repeat the process again for a strong double knot.
Once the knots are secure, you can release the clamps and cut the extra string on both sides, taking care not to cut the knots. Step 7. Begin the Cross Strings. The main strings are now finished so we can move on to the cross strings. At this point, you can reposition your clamps to accommodate the cross strings if your machine requires it you will only need one to hold the tension. To start off, take your other half of the string you reserved for cross strings and insert it into one of the shared holes you can tell by a slightly larger grommet at the top.
Tie a starting knot using one of the three methods shown below I prefer the fishing knot. Once your starting knot is secure, you will need to weave the string over and under the mains to reach the opposite aligning hole.
You can tell if you did it right if the the string you end on is the opposite of the one you started i. If you choose to tension the string after the first cross, just insert it into the gripper to pull the correct tension and clamp it as close to the grommet as possible. What I like to do, however, is weave a few crosses no more than 3 before I pull them. Once the starting cross strings are tensioned, continue stringing the crosses one at a time, repeating the process like before.
However, it is easier to first weave a cross and then tension the previous one by leaving a loop that can be inserted into the gripper. So, insert the string through the correct hole, weave the string over and under the mains, insert through the opposite aligning hole, leave a loop, pull tension on the previous cross, and then clamp it off. Use pliers when this is the case. The end is in sight! This is very similar to the knot we created for the main strings.
Simply find the closest hole that allows two strings to fit through. Insert the end of the cross string through and apply the same process as before: put the string down one side of the cross and up the other, putting the end of the string through the loop you just created.
If so, it might be time for you to restring. When polyester strings lose tension, there is a reduction in the snapback of the strings, which means you have to swing harder to generate the same amount of topspin as you would on a freshly strung racquet.
Polyester strings also develop dead spots, which causes an erratic response. If you find yourself hitting with less spin and you have to straighten your strings after every point, then it's probably time to restring.
The reason for writing this post is due to the following question received via email. Below that is my answer, adapted slightly into a more general one. Hi, do you have a general recommendation for frequency of restringing? I play 3 or 4 times a week, recreational mainly, but weekend doubles matches during the summer. Currently, I have Prince synthetic gut string at 53lb, in a Yonex DR , six months since last restring.
Any thoughts? When it comes to racquet restringing, there's a general rule of thumb that most players are familiar with which is:. Over a year, you should restring your racquet the number of times you play in a week. If you have not had a fresh string bed in six months, then I would say it's time to freshen things up.
Even if they look visually fine, the loss of tension and elasticity over time will have decreased the playability of the string. For most players, this concept of stringing as many times per year as you play per week is not a bad rule to follow. Especially for recreational players who string with a synthetic gut and aren't hitting a huge ball. However, the problem is that it's a rather broad blanket and can't be applied to all types of players or all kinds of string.
While the time you spend on the court is a significant factor, other considerations will determine the rate at which players get their racquets restrung. This only applies to non-string breakers as they have no choice but to restring as soon as a string pops, but factors include:.
Aggressive ball-strikers with full, heavy topspin strokes will wear through strings much faster than flat-hitting doubles specialists with abbreviated swings and touch play. For most players, a visual test is more suitable than abiding by a restringing calendar. My rule is based on both a visual look at the strings and how they play. If visually they look fine, but you play poorly in a match? Ok, it happens. Play the next match and the one after that badly?
It's probably time for a restring. Polyester strings are a tricky one to follow, and there's no real calendar rule to follow. Generally speaking, while polyester strings are hard to break for most club players, they go dead after 10 to 20 hours of play.
Not only that, but they also break down unevenly, which creates dead spots in the string bed, which can lead to erratic performance. However, because they don't break, players often keep them in their frames for too long. For this reason, it's's often recommended replacing polys every couple of months at a minimum to restore playability and reduce the risk of arm related injuries from having to swing harder to get the same amount of pace.
Ultimately, like most things to do with tennis racquets, restringing does boil down to personal preference and how the individual player feels about a racquet's performance. Many players love to play with a freshly strung racquet; others enjoy them more after a break-in period, and some even like strings when they are completely dead. I like a racquet pretty much just after it's freshly strung, so I usually restring my racquets before a more meaningful match.
Or if I know I'm playing a few times in the coming week, I'll bump up the tension, so when it comes to the second or third hit, the tension is somewhere around what it would be if it were fresh off the stringing machine at my desired tension. From there, it's all about keeping tabs on your play throughout the life of the string job.
Do I have to swing harder to create pace and spin? Are the strings biting the ball, or do I have to readjust them after every point?
0コメント